BWA - Works Boundary Plan BWA-M2G-SY-PLN-001 April 2010
Certificate of approval for issue of documents Document number BWA-M2G-SY-PLN-001 DM5 number Title BWA - Works Boundary Plan Revision 0 Document status Final Date of issue May 2010 Position Name Signature Date Prepared by Project Engineer Linda Garlick Original signed 18/5/2010 Reviewed by Construction Manager Jason Julius Original signed 18/5/2010 Approved by Project Manager Michael Mackintosh Original signed 19/5/2010 Document revision control Version Author Date Description Approval A Linda Garlick 22 April 2010 Issued for Review 0 Linda Garlick 18 May 2010 Issued for Approval ACTEW Corporation Ltd This publication is copyright and contains information that is the property of ACTEW Corporation Ltd. It may be reproduced for the purposes of use while engaged on ACTEW commissioned projects, but is not to be communicated in whole or in part to any third party without prior written consent. Disclaimer This document has been prepared for ACTEW and is to be used for internal purposes. No warranty is given as to its suitability for any other purpose.
Contents 1 PURPOSE 1 1.1 Reference Documents 1 2 MURRUMBIDGEE TO GOOGONG PROJECT 2 2.1 Scope of Works 2 3 PHYSICAL BOUNDARIES 3 3.2 Pipeline Easements 5 3.3 Electrical Line Easement 6 3.4 Low Lift Pump Station (Areas 1 and 2) 6 3.5 High Lift Pump Station (Area 3) 8 3.6 Angle Crossing Road Pipe Storage Area (Area 4) 8 3.7 Main Site Office Building Layout (Area 5) 9 3.8 Pipe Storage Area (Area 6) 10 3.9 Borrow Pit Pipe Storage Area (Area 7) 10 3.10 Mini Hydro Area (Area 8) 11 3.11 Discharge Structure Area (Area 9) 11 3.12 High Lift Pump Station Roadworks Upgrade 12 3.13 Monaro Highway and Angles Crossing Intersection Upgrade 12 4 FENCING 13 4.1 Temporary Fencing 13 4.2 Chainwire Fencing 13 4.3 Stock Fencing 13 Appendix A Drawings 14
1 PURPOSE The purpose of this plan is to outline the mitigation measures required when setting out the Murrumbidgee to Googong (M2G) project in accordance with the planning approvals. In accordance with the PAA Clause 16.5 the Works Boundary Plan The Alliance must develop and maintain at all times a Works Boundary Plan which specifies the boundaries of the Active Work Site for each Project at any time during the Program from the purpose of clause 10, this clause 16 and clause 28. The plan and all updates to the plan must be submitted to the APMT for agreement in accordance with clause 8. 1.1 Reference Documents This Document shall be read in conjunction with the Program Works Boundary Plan (BWA-PRW-SY-PLN- 005). BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 1
2 Murrumbidgee to Googong Project 2.1 Scope of Works The Murrumbidgee to Googong Water Transfer encompasses the construction and operation of pumping and pipeline infrastructure to transfer up to 100 ML/day of water approximately 12 km from the Murrumbidgee River at Angle Crossing (ACT), to the Googong Reservoir via run-of-river flow in Burra Creek (NSW). The project incorporates a: One metre diameter underground pipeline from the Murrumbidgee River over Gibraltar Pass to Burra Creek at Williamsdale Rd, a combined intake and low lift pump station at Murrumbidgee River, a high lift pump station, an 11 kv power supply, an outlet structure (within Burra Creek), and a mini-hydro power generator located near the outlet structure. The mini-hydro power generator will recover and reuse 25-30% of the pumping energy required to lift the water over the Gibraltar Range. The power generated will be transferred back to the high lift pump station through an underground cable in the same trench as the transfer pipeline. The project crosses the ACT / NSW Boarder just east of the Monaro Highway. 2 BULK WATER ALLIANCE APR L 2010
3 PHYSICAL BOUNDARIES The Physical Boundaries of each area vary dependant on the phase of the project. The table below shows the areas required in the final configuration and during the construction phase. These figures are taken from the EIS document (where detailed). Table 3.1 Area of Works Area of Works Jurisdiction Final Construction Permanent Structures Low Lift Pump Station (Area 1) Area 1A: Area 1B: Area 1C: ACT 750 m 2 40 m 2 250 m 2 3530 m 2 160 m 2 450 m 2 High Lift Pump Station (Area 3) ACT 4200 m 2 5500 m 2 Discharge Structure ( Area 9) NSW 1200 m 2 2600 m 2 Mini hydro (Area 8) NSW 250 m 2 5800 m 2 HLPS Roadwork Upgrade (Angle Crossing Road) Angle Crossing Road and Monaro Highway Intersection Upgrade ACT NA 2050 m 2 ACT NA 1100 m 2 Pipework Easements Chainage 0-94 ACT Easement 40m width Chainage 94-300 ACT Easement 35m width Chainage 450-692 ACT Easement 35m width Chainage 692-780 ACT Easement 40m width Chainage 780-820 ACT Easement 15m width Chainage 820-900 ACT Easement 35m width Chainage 900-985 ACT Easement 20m width Chainage 985-1060 ACT Easement 35m width Chainage 1060-1090 ACT Easement 20m width Chainage 1090-1750 ACT Easement 35m width Chainage 1750-2600 ACT Easement 25m width Chainage 2600-2650 ACT Easement 40m width Chainage 2650-2720 ACT Easement 20m width Chainage 2720-2760 ACT Easement 40m width BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 3
Area of Works Jurisdiction Final Construction Chainage 2760-2860 ACT Easement 20m width Chainage 2860-2900 NSW Easement 15m width Chainage 2900-3770 NSW Easement 25m width Chainage 3770-4200 NSW Easement 35m width Chainage 4200-4680 NSW Easement 25m width Chainage 4680-4720 NSW Easement 15m width Chainage 4720-5050 NSW Easement 30m width Chainage 5050-6470 NSW Easement 40m width Chainage 6470-7230 NSW Easement 15m width Chainage 7230-7510 NSW Easement 40m width Chainage 7510-7680 NSW Easement 35m width Chainage 7680-8020 NSW Easement 20m width Chainage 8020-8410 NSW Easement 30m width Chainage 8410-11250 NSW Easement 40m width Chainage 11250-11540 NSW Easement 25m width Chainage 11540-11690 NSW Easement 20m width Chainage 11690-11710 NSW Easement 40m width Electrical Easement Chainage 0 400 ACT Easement 20m width Temporary Areas Pipe Laydown Area 2 (Angle Crossing) Pipe Laydown Area 4 (Angle Crossing Cattle Grid) Incl PS site office Main Site Office (Area 5) Incl Storage Facility and Pipe storage area Pipe Laydown Area 6 (DP 754889 Property) ACT Temp Only 2300 m 2 ACT Temp Only 4200 m 2 ACT Temp Only 9500 m 2 NSW Temp Only 10000 m 2 Pipe Laydown Area 7 (Borrow Pit) NSW Temp Only 5000 m 2 4 BULK WATER ALLIANCE APR L 2010
3.2 Pipeline Easements The diagram show indicated typical layouts across each easement width. Please note these are only typical layouts and each area will be subject to unique site changes. Appendix A gives the pipeline plans showing the designated easement widths in each area. BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 5
3.3 Electrical Line Easement The electrical line between the Mini Hydro Station and the High Lift Pump Station will run in the one easement. However between the Low Lift Pump Station and the High lift Pump Station the electrical easement will be separate to the pipeline easement. This is due to constraints in the length of the electrical cable requirements, and as such the location of the electrical panel to be above regular flood levels. During construction the easement will be 20m wide. 3.4 Low Lift Pump Station (Areas 1 and 2) There are two areas within the lower Angle Crossing area. Area 1 is for the construction of the new Low Lift Pump Station, including associated equipment (Area 1A), and eductor pipework (Area 1B), electrical bunker (Area 1C) and Area 2 is the laydown area for this works. The laydown area will be used for the fabrication of formwork shutters, storage of pipework and mechanical equipment. Please note this diagram does not include the pipework or electrical easement sections. 6 BULK WATER ALLIANCE APR L 2010
Block 1572 Block 1611 Murrumbidgee River The figure below shows Area 1A proposed layout as a concept diagram. BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 7
3.5 High Lift Pump Station (Area 3) The High Lift pump station is located on the right side of Angles Crossing Road before the decent to the Murrumbidgee River Crossing. The figure below shows the final easement area and the construction easement. Not including the road works in Angles Crossing road required. 3.6 Angle Crossing Road Pipe Storage Area (Area 4) Located on the property (Block 1002A Tuggeranong) to the north west of the pipeline / road crossing area. This storage area will be located on property DP 1002A. Will be used to store pipes and fittings prior to installation or stringing along the route of the pipe. This area will also have a portable toilet facilities and crib rooms, with generator power supply. 8 BULK WATER ALLIANCE APR L 2010
Block 1636 Block 1572 Block 1654 3.7 Main Site Office Building Layout (Area 5) Total area is 9,500m2, located on Block 1471 Tuggeranong. The layout below is an indication of the usage of this area, final layout might be different. BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 9
3.8 Pipe Storage Area (Area 6) Located on private property (DP number 754889). Will be used to store pipes and fittings prior to installation or stringing along the route of the pipe. This area will also have a portable toilet facilities and crib rooms, with generator power supply or permanent power supply. Exact location and layout of area to be confirmed with the landowner prior to establishment. Area 6 100 x 100m 3.9 Borrow Pit Pipe Storage Area (Area 7) Located on the road reserve at Borrow Pit (Williamsdale Road). Will be used to store pipes and fittings prior to installation or stringing along the route of the pipe and additional materials for the mini hydro and discharge structure (as required). This area will also have a portable toilet facilities and crib rooms, with generator power supply or permanent power supply. 10 BULK WATER ALLIANCE APR L 2010
3.10 Mini Hydro Area (Area 8) The mini hydro is located between the new Williamsdale Road and the old section. This area will be utilised during construction for the storage of all the mechanical equipment associated with the Mini Hydro Plant prior to installation. This area will also have a portable toilet facilities and crib rooms, with generator power supply or permanent power supply. The final easement includes an access track to the station, from Williamsdale Road. 3.11 Discharge Structure Area (Area 9) This discharge structure is located in Burra Creek. This area will be used to store materials required during the construction of the discharge structure. The final layout of the access road to the discharge structure will be from Williamsdale Road. BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 11
3.12 High Lift Pump Station Roadworks Upgrade The entrance to the high lift pump station on Angles Crossing Road is required to be upgraded. A traffic management plan for this area will be developed to ensure the road remains open to traffic during the upgrade works. 3.13 Monaro Highway and Angles Crossing Intersection Upgrade Prior to construction works beginning the intersection at Monaro Highway and Angles Crossing is to be upgraded. The design of this intersection upgrade has been reviewed and approved by the National Capital Authority. 12 BULK WATER ALLIANCE APR L 2010
4 Fencing Each area of work will be isolated from the surrounding area utilising boundary fences. A combination of these 3 types of fencing will be used in each area. 4.1 Temporary Fencing Temporary fencing shall be utilised extensively throughout this project. It will be used around all Pipe storage areas and at the Low Lift Pump Station area. 4.2 Chainwire Fencing This type of fence, although permanent can be removed with ease at the completion of the project. This type of fence will only be used around the Main Office complex. 4.3 Stock Fencing To be used along each side of the construction corridor. In conjunction with this temporary and permanent gates will be installed. BWA - WORKS BOUNDARY PLAN BWA-M2G-SY-PLN-001 13
Appendix A Drawings 14 BULK WATER ALLIANCE APR L 2010
Area 1 Area 1 Area 2 Area 2 Electrical Chamber Area 4 Area 3 Electrical Line Easement Monaro Highway Intersection Area 5 Area 3 Road upgrade area Area 6 Area 8 Area 9 Area 7 Area 8 Area 9