SECTION A : 50 MARKS BAHAGIAN A : 50 MARKAH INSTRUCTION: This section consists of TWO (2) structured questions. Answer ALL questions. ARAHAN: Bahagian ini mengandungi DUA (2) soalan berstruktur. Jawab SEMUA soalan. QUESTION 1 SOALAN 1 CLO1 C1 a) Define the terms below: Berikan maksud istilah-istilah di bawah: i) Cadastral [2 marks] Kadaster [2 markah] ii) Cadastral Survey Ukur Kadaster [3 marks] [3 markah] CLO1 b) Describe FIVE (5) functions of State Department of Survey And Mapping Malaysia Pilih LIMA (5) fungsi Jabatan Ukur Dan Pemetaan Malaysia (JUPEM) Negeri CLO1 c) Application for survey is a term used for seeking permission from authorities to perform survey work. Using a suitable diagram, identify the procedure of application for survey. Permintaan Ukur adalah istilah yang digunakan bagi mendapatkan kebenaran kerajaan untuk menjalankan kerja ukur. Dengan menggunakan gambarajah yang sesuai, tentukan prosedur yang perlu dilalui untuk melakukan permintaan ukur. 2
QUESTION 2 SOALAN 2 CLO1 Explain the following cadastral terms. Terangkan istilah-istilah kadaster berikut. i. Cadastral Reference Mark (CRM) [3marks] Stesen Tanda Rujukan Ukur Kadaster (CRM) ii. Geocentric Datum Malaysia (GDM2000) [3marks] Datum Geosentrik Malaysia (GDM2000) iii. Long Line [3marks] Garisan Panjang iv. Short Line [3marks] Garisan Pendek v. National Digital Cadastral Database (NDCDB) [4marks] Pangkalan Data Ukur Kadaster Berdigit Kebangsaan [4markah] vi. Geocentric Cassini Coordinate System [3marks] Sistem Koordinat Cassini Geosentrik vii. Single Leg [3marks] Single Leg viii. Geocentric RSO Coordinate System [3marks] Sistem Koordinat Geosentik RSO 3
SECTION B :50 MARKS BAHAGIAN B : 50 MARKAH INSTRUCTION: This section consists of FOUR (4) structured questions. Answer TWO (2) questions only. ARAHAN: Bahagian ini mengandungi EMPAT (4) soalan berstruktur. Jawab DUA (2) semua soalan sahaja. QUESTION 1 SOALAN 1 a) Identify FIVE (5) situation which require EDM to be calibrated [5 marks] Tentukan LIMA (5) situasi dimana EDM perlu dikalibrasi [5 markah] b) Differential Field Test (DFT) is one of the tests conducted on the Electronic Distance Measurement (EDM). Illustrate the procedure of Differential Field Test. Differential Field Test (DFT) adalah salah satu ujian yang dijalankan pada alat Electronic Distance Measurement (EDM). Gambarkan prosedur Differential Field Test tersebut. 4
(c) By using Appendix 1, calculate and complete the Calibration test form below. Dengan menggunakan Lampiran 1,Kira dan lengkapkan borang ujian kalibrasi di bawah; PILLAR NO. MEASURED HORIZONTAL ORIGINAL BASIC FROM TO DISTANCE DISTANCE (A) DISTANCE DIFFERENCES (B) ( A - B ) 1 2 4.998 5.001-0.003 1 3 10.030 10.036 1 4 50.001 49.998 0.003 1 5 87.310 87.316-0.006 1 6 125.550 125.554 1 7 163.007 163.010 1 8 200.999 200.998 1 9 251.004 251.006 1 10 300.498 300.500-0.002 2 3 5.097 5.110-0.013 2 4 44.514 44.512 0.002 2 5 82.166 82.171 2 6 120.231 120.236 2 7 158.995 158.998-0.003 2 8 196.505 196.510-0.005 2 9 246.773 246.771 0.002 2 10 295.418 295.415 TANDATANGAN JURUKUR NAMA JURUKUR: = 5
QUESTION 2 SOALAN 2 a) Survey datum is the main requirement for each new survey to enable the determination of planimetry control and coordinate value. Each cadastral survey must be based on satisfied and sufficient datum. Based on the statement above, interpret the conditions of datum that has been applied and practice in Peninsular Malaysia for cadastral work according to Survey Regulation 2009. Datum ukuran adalah satu keperluan utama bagi setiap ukuran baru untuk membolehkan penentuan asas planimetri ukuran dan nilai koordinat. Setiap ukuran ukur kadaster mestilah berdasarkan kepada datum yang memuaskan dan mencukupi. CLO 2 Berdasarkan petikan di atas, terangkan syarat- syarat datum yang diguna dan diamalkan di Semenanjung Malaysia bagi kerja ukur kadaster berdasarkan Peraturan Ukur 2009. CLO 2 b) i) By using an appropriate sketch, explain close traverse and open traverse. Dengan menggunakan lakaran yang sesuai, terangkan trabas terbuka dan trabas tertutup. ii) List the general statements for cadastral closed traverse. Senaraikan penyataan trabas tertutup dalam ukur kadaster [5 marks] [5 markah] 6
QUESTION 3 SOALAN 3 a) Sketch and explain clearly the procedure of EDM calibration test. Terangkan dengan jelas prosedur ujian kalibrasi EDM b) By using the data from Table B3, complete the traverse booking with C correction for this close traverse if the given bearing of BKL 1 BKL 2 is 225 55 40. (Use Appendix 2 to answer your question) Dengan menggunakan data dari Jadual B3,lengkapkan pembukuan trabas beserta pembetulan C bagi trabas tertutup tersebut jika bearing dari BKL 2 BKL 1 adalah 225 55 40. (Sila guna Lampiran 2 untuk menjawab) [15 marks] [15 markah] 7
Table B3 / Jadual B3 Line BKL 2 BKL 1 Bearing Distance Face Left Face Right Face Left Face Right Datum dari PA 02-240714 225 55 '40" BKL 2-3 95 22' 46" 275 22 46 82.931 82.931 3-4 139 35' 38" 319 35 40 84.185 84.183 4-5 165 16' 29" 345 16 30 97.988 97.984 5-6 74 00' 53" 254 00 53 52.870 52.865 6 BKL 1 327 06' 43" 147 06 43 80.471 80.471 BKL 1 BKL 2 45 55' 50" 225 55 50 85.125 85.125 8
QUESTION 4 SOALAN 4 a) Relate the use of Cadastral Reference Mark (CRM) and old boundary mark in cadastral survey work. Nyatakan hubungkait penggunaan Cadastral Reference Mark (CRM) dengan sempadan lama dalam kerja ukuran kadaster. [5 marks] [5 markah] CLO 1 b) i) One of the fuctions of cadastral survey is for planning and development of land. Explain clearly the above statement with suitable examples. Salah satu kegunaan ukur kadaster adalah untuk perancangan dan pembangunan tanah. Terangkan dengan jelas ayat diatas bersama contoh yang sesuai. CLO 1 ii) Certified Plan (CP) and Standard Sheet are two things related to cadastral survey. Explain the function and relationship of these two plans. Pelan Akui (PA) dan Standard Piawai adalah dua perkara yang berkaitan dengan ukur kadaster. Huraikan fungsi dan hubungkait dua pelan tersebut. SOALAN TAMAT 9